高g值加速度冲击试验技术研究

摘 要：根据弹体高速侵彻硬目标过程中加速度测试的特点,研制了高g值冲击试验装置。它由一级空气炮、加速度存储测试装置、炮弹、反射式激光测速仪和激光多普勒测速仪等组成,并在该冲击试验装置上进行了弹载加速度存储测试装置的高g值冲击试验。采用泡沫铝缓冲件对记录电路模块进行缓冲保护,利用光栅作为合作目标,由两套激光多普勒测速仪同时记录冲击过程中测试装置外壳和电路模块的激光频移信号, 处理可得到二者的加速度——时间曲线,比较了泡沫铝的高g值缓冲效果。     

缓冲气体及温度对DPAL输出性能的影响

为进一步提高半导体激光泵浦碱金属蒸汽激光器输出功率,基于三能级速率方程的理论模型,对DPAL的运行进行了模拟,考虑泵浦光带宽,在纵向泵浦的情况下,对缓冲气体气压、增益池长度、温度等参量对激光器输出光强及光光效率的影响进行了计算机模拟,结果表明,一定泵浦光下光光效率随着乙烷气压和温度增加而增大,对一定氦气气压有最大值,模拟结果为实验研究提供了有益的参考。     

基于MoO3和Re-Bphen修饰有机太阳能电池性能的研究

有机太阳能电池(OSCs)的性能与材料及器件结构密切相关。以MoO3为阳极缓冲层,有机金属配合物Re-Bphen为阴极缓冲层,制备了结构为ITO/MoO3/CuPc/C60/Re-Bphen/Al的OSCs。在标准太阳光照条件下,当MoO3和Re-Bphen的厚分别为5nm和8nm时实现了器件的最佳性能,能量转换效率(PCE)和器件寿命均显著提高。结合器件结构,分析了工作机制。     

酵母常规透射电镜样品制备方法的比较与改进

透射电镜技术中前期样品制备是获得最接近样品真实结构信息的关键。本文选择酵母为观察对象,运用常规样品制备技术,观察不同缓冲液、不同脱水时间和脱水温度对酵母超微结构的影响,优化了酵母常规透射电镜前期制样方案。     

电梯液压缓冲器缓冲特性研究

为了获取电梯用液压缓冲器复位弹簧刚度、缓冲质量、下落速度对缓冲特性的影响规律,应用质量守恒方程和能量守恒方程建立了缓冲器液压阻力数学模型,采用数值分析的方法对不同复位弹簧刚度、不同缓冲质量、不同下落速度工况下的缓冲特性进行了分析。结果表明:复位弹簧刚度对缓冲性能有一定影响但优化的空间并不大;在重载工况下,该液压缓冲器满足性能要求,在轻载工况下,缓冲行程较短但缓冲减速度较大;随着下落速度的增大,缓冲过程平均减速度、最大减速度、缓冲行程均随之增大。     

多孔调湿材料湿缓冲特性的实验研究

利用NORDTEST实验方法对中国长江中下游地区(以南京为例)多孔调湿材料的湿缓冲值(Moisture Buffer Value)进行测定,同时,研究湿缓冲值对建筑能耗及室内湿度的影响。实验结果显示,高湿度区间内材料的湿缓冲测定值较大,且不同材料的湿缓冲值存在较大差异。分析表明在长江中下游地区,使用具有吸放湿特性的建筑内表面材料可有效降低建筑能耗10%以上,同时,室内环境湿度也会得到一定程度的调节。     

A reliable and sensitive time-resolved fluorescent immunochromatographic assay (TRFICA) for ochratoxin A in agro-products

Immunochromatographic assays (ICAs) are considered as a suitable diagnostic tool for the detection of mycotoxins. Mycotoxins and especially, ochratoxin A are analytes with more demanding sensitivity requirements. To enhance the sensitivity of current immunochromatographic assays for ochratoxin A (OTA), a novel sensitive ICA was developed in this study. In the assay, microspheres enclosing fluorescent europium (III) [Eu(III)] nanoparticles (EuNPs) were used as a label for OTA monoclonal antibody (OTA-mAb) conjugation. Accordingly, assay was called time-resolved fluorescent immunochromatographic assay (TRFICA). The test strip was composed of three parts: a sample pad, nitrocellulose membrane and an absorbent pad. As for detection, a proper concentration of conjugated microspheres was pipetted into the microtube and sample extract was added to it. Then the strip was inserted into the tube and the fluid flow along the strip. The TRFICA results were obtained in 8 min and read by a portable TRFICA strip reader. The established method allows quantitative determination of OTA with limit of detection as low as 1.0 μg kg⁻¹ in the samples. For validation, spiked samples including wheat, maize, soybean and rice were respectively assayed by TRFICA and a standard high performance liquid chromatography equipped with a fluorescence detector (HPLC-FLD), and good agreement of results was obtained between two methods.     

CAWR: Buffer Replacement with Channel‐Aware Write Reordering Mechanism for SSDs

A typical solid‐state drive contains several independent channels that can be operated in parallel. To exploit this channel‐level parallelism, a variety of works proposed to split consecutive write sequences into small segments and schedule them to different channels. This scheme exploits the parallelism but breaks the spatial locality of write traffic; thus, it is able to significantly degrade the efficiency of garbage collection. This paper proposes a channel‐aware write reordering (CAWR) mechanism to schedule write requests to different channels more intelligently. The novel mechanism encapsulates correlated pages into a cluster beforehand. All pages belonging to a cluster are scheduled to the same channels to exploit spatial locality, while different clusters are scheduled to different channels to exploit the parallelism. As CAWR covers both garbage collection and I/O performance, it outperforms existing schemes significantly. Trace‐driven simulation results demonstrate that the CAWR mechanism reduces the average response time by 26% on average and decreases the valid page copies by 10% on average, while achieving a similar hit ratio to that of existing mechanisms.     

Structural and opto-electrical properties of pyrolized ZnO-CdO crystalline thin films

A series of ZnO-CdO thin films of different molar ratios of Zn and Cd have been deposited on glass substrate at substrate temperature ~ 360 ℃ by the spray pyrolysis technique at an ambient atmosphere. X-ray diffraction (XRD) studies confirmed the polycrystalline nature of the film and modulated crystal structures of wurtzite (ZnO) and cubic (CdO) are formed. The evaluated lattice parameters, and crystallite size are consistent with literature. Dislocation density and strain increased in the film as the grain sizes of ZnO and CdO are decreased. The band gap energy varies from 3.20 to 2.21 eV depending on the Zn/Cd ratios in the film. An incident photon intensity dependent I-V study confirmed that the films are highly photosensitive. Current increased with the increase of the intensity of the light beam. The optical conductivity and the optical constants, such as extinction coefficient, refractive index and complex dielectric constants are evaluated from transmittance and reflectance spectra of the films and these parameters are found to be sensitive to photon energy and displayed intermediate optical properties between ZnO and CdO, making it preferable for applications as the buffer and window layers in solar cells.     

一款高性能时钟驱动器电路的设计

时钟器件芯片可以实现通信网定时同步、时钟产生、时钟恢复和抖动滤除、频率合成和转换、时钟分发和驱动等功能。在系统设计中,选用好的时钟驱动芯片,可以省去系统时钟树设计,既节省空间,又提高系统性能。介绍一款高性能时钟驱动器的集成电路设计方法,主要性能要求有:低传播延时、低输出偏斜、低输出抖动、抗电磁干扰能力、抗ESD能力,一一详述了达到各项要求的设计。